Skip to content
Research Article Open access CC BY 3.0

Waste Plastics: Pyrolysis of Powdered and Powder-free Laboratory Examination Waste Gloves

Nasrollah Hamidi, Ruhullah Massoudi, Sujan Shrestha, Lycinda Lalmansingh, Travis Pascoe, Comfort Oriakhi, Louis Whitesides

Current Journal of Applied Science and Technology · pp. 967–1019 · Published 27 Dec 2013

10.9734/BJAST/2014/6375

Abstract

Aims: The aim of this investigation was to develop a methodology that provides insights to clean up environmental pollution caused by the ever increasing amount of waste plastic materials. The procedure, however, would be practical whenever it is economically advantageous. Thermal cracking of laboratory safety glove (LSG), without catalyst, to useful chemicals is an important part of this research which is reported here. Study Design: To design the experimental procedure, we primarily concentrated on the thermal stability of the LSG by bearing in mind the results of thermo gravimetric analysis (TGA). Based on such results the appropriate set-up for the decomposition of the LSG was designed. Place and Duration of Study: The study was done in the Department of Biological and Physical Sciences at South Carolina State University (SCSU), Orangeburg, SC, USA, during the summer of 2013. Methodology: The thermal cracking process without catalyst was used to convert LSGs into useful liquid and solid chemicals. The LSGs were pushed into the reactor one by one without cutting. Prior to pyrolysis, the thermal stability of materials were determined by thermo gravimetric analysis (from 50ºC to 800ºC) with a heating rate of 10ºC/min while the samples were purged with 10 mL/min argon. The condensed liquids were analyzed by a Shimadzu GC-MS model GCMS-QP 2010s using helium as the mobile phase. Results: The thermal stability of the LSG both powdered and powder-free was very similar as was expected since it depended on the nature of constituent polymers. The highest decomposition rates were observed at temperatures around 410ºC. The 15% leftover of the powder-free LSG were less than leftover of powered LSG (30%) at 500ºC, in the same way the 18% leftover ashes of powdered LSG was higher than 7% ashes of powdered free LSG at 800ºC. The GC-MS chromatogram of pyrolysis liquids indicated over 350 chemicals. The most abundant compound of pyrolysis was HCl, as was expected from the chemical constituents of chlorinated plastics, followed with eight member carbon isomers. Also, a variety of phthalic acid derivatives with high concentration were recognized in all samples. Conclusion: The liquids obtained from pyrolysis of LSGs were a complex mixture of hydrocarbons and cyclic compounds. Also, the liquids were saturated with inorganic and organic acids, esters and anhydrides. Therefore, the refinement of liquids resulting from pyrolysis is of necessity to obtain a quality fuel. Also, the condensed liquids contained highly reactive chemicals such as acids, alcohols and alkene, which made them unsuitable fuel for internal combustion engines prior to refinement.

Environment pollution lab examination gloves latex gloves pyrolysis of gloves neoprene pyrolysis of waste gloves chemicals from pyrolysis of gloves phthalic acid derivatives

References (27)

  1. 1 Chemical recycling of plastic wastes made from polyethylene (LDPE and HDPE) and polypropylene (PP) [DOI]
  2. 2 Composition of products from the pyrolysis of polyethylene and polystyrene in a closed batch reactor: Effects of temperature and residence time [DOI]
  3. 3 Feedstock Recycling and Pyrolysis of Waste Plastics [DOI]
  4. 4 Fluidised bed pyrolysis of low density polyethylene to produce petrochemical feedstock [DOI]
  5. 5 Co-pyrolysis of pine cone with synthetic polymers [DOI]
  6. 6 Feedstock recycling of polymers by pyrolysis in a fluidised bed [DOI]
  7. 7 Pyrolysis of plastic wastes. 1. Effect of plastic waste composition on product yield [DOI]
  8. 8 Characterization of Products from the Pyrolysis of Municipal Solid Waste [DOI]
  9. 9 Analysis of products derived from the fast pyrolysis of plastic waste [DOI]
  10. 10 Science and technology of rubber reclamation with special attention to NR-based waste latex products [DOI]
  11. 11 Study on pyrolysis of typical medical waste materials by using TG-FTIR analysis [DOI]
  12. 12 Vacuum pyrolysis of commingled plastics containing PVC II. Product analysis [DOI]
  13. 13 Toxicity of the pyrolysis and combustion products of poly(vinyl chlorides): A literature assessment [DOI]
  14. 14 Pyrolysis of plastic wastes [DOI]
  15. 15 Kinetic modeling of the thermal degradation of polyethylene and polystyrene mixtures [DOI]
  16. 16 Pyrolysis of oil sludge in a fluidised bed reactor [DOI]
  17. 17 Pyrolysis of styrene, acrylate, and isoprene polymers in a vacuum [DOI]
  18. 18 Study of the Pyrolysis Kinetics of a Mixture of Polyethylene, Polypropylene, and Polystyrene [DOI]
  19. 19 Isothermal co-pyrolysis of hazelnut shell and ultra-high molecular weight polyethylene: The effect of temperature and composition on the amount of pyrolysis products [DOI]
  20. 20 Bed defluidisation during the fluidised bed pyrolysis of plastic waste mixtures [DOI]
  21. 21 Catalytic Pyrolysis of Low-Density Polyethylene over Alumina-Supported Noble Metal Catalysts [DOI]
  22. 22 Conversion of Low Density Polyethylene (LDPE) and Polypropylene (PP) Waste Plastics into Liquid Fuel Using Thermal Cracking Process [DOI]
  23. 23 Analysis of Pyrolyzates of Polystyrene and Poly(methyl Methacrylate) by Gas Chromatography [DOI]
  24. 24 Study on thermal decomposition processes of polysiloxane polymers—From polymer to nanosized silicon carbide [DOI]
  25. 25 Reaction Kinetic Model for Optimal Pyrolysis of Plastic Waste Mixtures [DOI]
  26. 26 Pyrolysis of Waste Polystyrene and High-Density Polyethylene [DOI]
  27. 27 Thermal degradation of heavy pyrolytic oil in a batch and continuous reaction system [DOI]

Cited by 9

Kinetics of Powder-Free Laboratory Examination Gloves at 323°C and 408°C by Thermogravimetric Analysis

Nasrollah Hamidi · Advances in Research · 2015

A marine bacterial strain with polyurethane-degrading activity, a potential for plastic waste control in the oceans

Nallely Magaña-Montiel, Luis Felipe Muriel-Millán, Jorge Rojas-Vargas · Marine Pollution Bulletin · 2025

Experimental evaluation of product yield by pyrolysis of medical waste: a way of energy recovery

Md. Abdullah Al- Mamun, Md. Mushrafi Al- Mueed, Md. Hasan Ali · South African Journal of Chemical Engineering · 2025

Showing 3 of 9 known citations — external sources report more than can currently be individually listed.

Related research

Article metrics

Real usage data collected on this platform.

13

Page views

0

PDF downloads

1

Outbound clicks

9

Citations

Views over time

Views by country

Approximate, from request IP at view time — not citizenship or institution. Countries with fewer than 5 views are grouped as "Other".

Traffic sources

Referring site, by host.

Views and downloads exclude known bots/crawlers. Citations combines this platform's own DOI-resolved index with each external source's own reported total — see Cited by above for individually listed citing works. Last refreshed 0 seconds ago.