Investigation of Mechanical, Corrosion and Microstructural Behaviour of Heat Treated Cr-Modified Al-Mg-Si Alloy

References (41)

1. 1 Validation of corrosion rates measured by the Tafel extrapolation method [DOI]
2. 2 Selective laser melting of AlSi10Mg alloy: Process optimisation and mechanical properties development [DOI]
3. 3 The microstructure and mechanical properties of selectively laser melted AlSi10Mg: The effect of a conventional T6-like heat treatment [DOI]
4. 4 Precipitation of dispersoids containing Mn and/or Cr in Al–Mg–Si alloys [DOI]
5. 5 Effect of substitution on corrosion inhibition properties of 2-(substituted phenyl) benzimidazole derivatives on mild steel in 1 M HCl solution: A combined experimental and theoretical approach [DOI]
6. 6 Insights into corrosion inhibition behavior of three chalcone derivatives for mild steel in hydrochloric acid solution [DOI]
7. 7 Effect of natural ageing or pre-ageing on the evolution of precipitate structure and strength during age hardening of Al–Mg–Si alloy AA 6016 [DOI]
8. 8 Aminoazobenzene and diaminoazobenzene functionalized graphene oxides as novel class of corrosion inhibitors for mild steel: Experimental and DFT studies [DOI]
9. 9 Development of a super ductile diecast Al–Mg–Si alloy [DOI]
10. 10 Effect of heat treatment on microstructure, hardness and corrosion resistance of 7075 Al alloys fabricated by SLM [DOI]
11. 11 A Review on the Heat Treatment of Al-Si-Cu/Mg Casting Alloys [DOI]
12. 12 The effects of Cu addition on the microstructure and thermal stability of an Al–Mg–Si alloy [DOI]
13. 13 Improvement of elevated-temperature strength and recrystallization resistance via Mn-containing dispersoid strengthening in Al-Mg-Si 6082 alloys [DOI]
14. 14 Formability and strengthening mechanism of solution treated Al–Mg–Si alloy sheet under hot stamping conditions [DOI]
15. 15 The mechanism of grain refinement and plasticity enhancement by an improved thermomechanical treatment of 7055 Al alloy [DOI]
16. 16 Pre-strain-dependent natural ageing and its effect on subsequent artificial ageing of an Al-Cu-Li alloy [DOI]
17. 17 Effect of varying TiB2 reinforcement and its ageing behaviour on tensile and hardness properties of in-situ Al-4.5%Cu-xTiB2 composite [DOI]
18. 18 The influence of Cu addition and pre-straining on the natural aging and bake hardening response of Al-Mg-Si alloys [DOI]
19. 19 Effect of Zr, Cr and Sc on the Al–Mg–Si–Mn high-pressure die casting alloys [DOI]
20. 20 Grain refinement and improved tensile properties of Mg–3Al–1Zn alloy processed by low-temperature indirect extrusion [DOI]
21. 21 Clustering behavior during natural aging and artificial aging in Al-Mg-Si alloys with different Ag and Cu addition [DOI]
22. 22 Precipitation strengthening mechanisms during natural ageing and subsequent artificial aging in an Al-Mg-Si-Cu alloy [DOI]
23. 23 Microstructure and crystallography of borides and mechanical properties of Fe–B–C–Cr–Al alloys [DOI]
24. 24 Combination of sever plastic deformation and precipitation hardening processes affecting the mechanical properties in Al–Mg–Si alloy [DOI]
25. 25 Effect of water-soluble chitosan on the electrochemical corrosion behaviour of mild steel [DOI]
26. 26 Optimizing the defensive characteristics of mild steel via the electrodeposition of Zn Si3N4 reinforcing particles [DOI]
27. 27 Strengthening mechanisms in an Al-Fe-Cr-Ti nano-quasicrystalline alloy and composites [DOI]
28. 28 Effect of alloy composition on hot deformation behavior of some Al-Mg-Si alloys [DOI]
29. 29 Enhancing the bake-hardening responses of a pre-aged Al-Mg-Si alloy by trace Sn additions [DOI]
30. 30 5083 type Al-Mg and 6082 type Al-Mg-Si alloys for ship building [DOI]
31. 31 Effect of Ni addition on microstructure and mechanical properties of Al–Mg–Si–Cu–Zn alloys with a high Mg/Si ratio [DOI]
32. 32 Behaviour of Al-Mg-Si alloys at a wide range of temperatures and strain rates [DOI]
33. 33 Anticorrosive Properties of Chitosan for the Acid Corrosion of Aluminium [DOI]
34. 34 7xxx aluminum alloys; strengthening mechanisms and heat treatment: a review [DOI]
35. 35 Optimized nanoporous alumina coating on AA3003-H14 aluminum alloy with enhanced tribo-corrosion performance in palm oil [DOI]
36. 36 Effect of Solid Solution and Ageing Treatments on the Microstructure and Mechanical Properties of the SiCp/Al-Si-Cu-Mg Composite [DOI]
37. 37 Effect of Mn and Cr additions on kinetics of recrystallization and parameters of grain-boundary relaxation of Al-4.9Mg alloy [DOI]
38. 38 Reliability Analysis of Brinell Hardness Results for Aged Alumix321/SiC Composites [DOI]
39. 39 Design, Development and Performance Evaluation of A 5-Ton Capacity Brinell Hardness Testing Machine [DOI]
40. 40 Transactions of the Indian Institute of Metals [DOI]
41. 41 Quench Sensitivity of 6xxx Aluminum Alloys

Cited by 0

No indexed citations yet.

Related research

• Heavy Metal Toxicity and Contamination of Fishes in Port Harcourt Creeks: A Systematic Review of Evidence Integration of Lead, Chromium, and Cadmium Exposure, Impact, and Health Risks — shares topic coverage
• Biosorption of Heavy Metals by Oscillatoria Species — shares topic coverage
• Evaluation of the Concentrations of Some Heavy Metals (Pb, Cd and Cr) and Long Term Exposure Due to Daily Consumption of Ready-to-Eat Foods Sold at Petrol Station’s Atmospheric Conditions (AF) in Calabar Metropolis — shares topic coverage
• Synergism of Heavy Metals on the Respiration of Oreochromis mossambicus — shares topic coverage
• Bioremediation of Chromium, Nickel and Zinc in Electroplating Effluent by Escherichia coli — shares topic coverage