Skip to content
Research Article Open access CC BY 3.0

Dry Sliding Wear Behavior of Aluminium Matrix Composite Using Red Mud an Industrial Waste

Naresh Prasad, Harekrushna Sutar, Subash Chandra Mishra, Santosh Kumar Sahoo, Samir Kumar Acharya

International Research Journal of Pure and Applied Chemistry · pp. 59–74 · Published 2 Mar 2013

10.9734/IRJPAC/2013/2906

Abstract

The effect of fillers like red mud (RM) on dry sliding wear behavior of pure aluminium has been experimentally investigated. Pure aluminium of IE-07 grades from National Aluminium Company (NALCO), Angul of Odisha, India being collected with fillers in 10%, 15%, 20% and 30% based on weight were prepared using a stir casting technique. The dry sliding wear tests were conducted using pin-on-disc wear test machine. Tests were conducted for a sliding distance from 4.53×103m to 27.18×103m with wear track diameter 50mm-180mm. For each composition wear tests were conducted for different sliding speeds of 200 rpm (1.257m/s), 300 rpm (1.885m/s) and 400 rpm (3.141m/s) by applying normal loads of 10N, 20N and 30N. The wear rate and coefficient of friction were plotted against the normal load, sliding velocity and sliding distance for each filler composition. The results reveal that incorporation of red mud fillers leads to significant improvement in wear resistance of aluminium. The effect is the increase in interfacial area between aluminium matrix and red mud particles leading to the increase in strength appreciably.  

Aluminum matrix red mud fillers wear characteristics

References (17)

  1. 1 Correlation between the characteristics of the mechanically mixed layer and wear behaviour of aluminium, Al-7075 alloy and Al-MMCs [DOI]
  2. 2 Wear behaviour of SiCp-reinforced magnesium matrix composites [DOI]
  3. 3 Wear mechanism maps for metal matrix composites [DOI]
  4. 4 Dry sliding wear of fly ash particle reinforced A356 Al composites [DOI]
  5. 5 Friction and wear behavior of Ni–P coated Si3N4 reinforced Al6061 composites [DOI]
  6. 6 Effect of matrix alloy and influence of SiC particle on the sliding wear characteristics of aluminium alloy composites [DOI]
  7. 7 Dry sliding friction and wear properties of B4C particulate-reinforced Al-5083 matrix composites [DOI]
  8. 8 Wear of different aluminum matrix composites under conditions that generate a mechanically mixed layer [DOI]
  9. 9 Wear behavior of Al–Mg–Cu–based composites containing SiC particles [DOI]
  10. 10 RETRACTED: Dry sliding wear behaviour of cast high strength aluminium alloy (Al–Zn–Mg) and hard particle composites [DOI]
  11. 11 The sliding wear behavior of Al6061–garnet particulate composites [DOI]
  12. 12 Dry sliding wear of garnet reinforced zinc/aluminium metal matrix composites [DOI]
  13. 13 The relevance of wear-mechanism maps to mild-oxidational wear [DOI]
  14. 14 Dry sliding wear behaviour of aluminum syntactic foam [DOI]
  15. 15 Analyzing dry sliding wear behaviour of copper matrix composites reinforced with pre-coated SiCp particles [DOI]
  16. 16 The wear of wrought aluminium alloys under dry sliding conditions [DOI]
  17. 17 Modeling steady wear of steel/Al2O3Al particle reinforced composite system [DOI]

Cited by 71

Characterization of Plasma Sprayed Pure Red Mud Coatings: An Analysis

Alok Satapathy, Harekrushna Sutar, Subash Chandra Mishra, Santosh Kumar Sahoo · Chemical Science International Journal · 2013

Tribological Aspects of Thermally Sprayed Red Mud-Fly Ash and Red Mud-Al Coatings on Mild Steel

Harekrushna Sutar, Subash Chandra Mishra, Santosh Kumar Sahoo, Himanshu Sekhar Maharana, Ananta Prasad Chakraverty · Chemical Science International Journal · 2014

Progress of Red Mud Utilization: An Overview

Harekrushna Sutar, Subash Chandra Mishra, Santosh Kumar Sahoo, Ananta Prasad Chakraverty, Himanshu Sekhar Maharana · Chemical Science International Journal · 2014

Friction and Wear Behaviour of Plasma Sprayed Fly Ash Added Red Mud Coatings

Harekrushna Sutar, Debashis Roy, Subash Chandra Mishra, Ananta Prasad Chakraverty, Himanshu Sekhar Maharana · Physical Science International Journal · 2014

A review on monolithic and hybrid metal–matrix composites reinforced with industrial-agro wastes

Gaurav Arora, Satpal Sharma · Journal of the Brazilian Society of Mechanical Sciences and Engineering · 2017

Assessment of Tribological Performance of Al-Coconut Shell Ash Particulate—MMCs using Grey-Fuzzy Approach

Sivasankara Raju Rallabandi, Gunji Srinivasa Rao · Journal of The Institution of Engineers (India): Series C · 2017

Sliding Wear Performance Evaluation of Red Mud (RM), RM + Fly Ash (FA) and RM + FA + Al Coatings on Mild Steel

Harekrushna Sutar, Debashis Roy, Subash Chandra Mishra · Materials Sciences and Applications · 2016

Tribological Behavior of Al6061 Alloy Reinforced with Fly Ash Particles

D. A. Nayana, Mailareppa Marachakkanavar, Nagaraj Kantli · Techno-Societal 2016 · 2017

Showing 24 of 71 known citations — external sources report more than can currently be individually listed.

Article metrics

Real usage data collected on this platform.

156

Page views

0

PDF downloads

54

Outbound clicks

71

Citations

Views over time

Views by country

Approximate, from request IP at view time — not citizenship or institution. Countries with fewer than 5 views are grouped as "Other".

Traffic sources

Referring site, by host.

Views and downloads exclude known bots/crawlers. Citations combines this platform's own DOI-resolved index with each external source's own reported total — see Cited by above for individually listed citing works. Last refreshed 0 seconds ago.